Click Here to Visit our Original Site
  • Home
  • How to Order
  • Contact
  • Site map
  • Privacy
719-676-3928 Live Chat! Email Us

ESD Wrist Strap and Table Top Monitor

Powerful Performance, Outstanding Value!

OUR PRODUCTS

ESD Concrete Sealer

ESD Vinyl Tile

ESD Carpet Tile

ESD Sheet Floors

ESD Epoxy Floor Paint

ESD Wax, ETC

ESD Matting

ESD Constant Monitors

Wrist & Heel Straps

ESD Ionizers

ESD Test Equipment

ESD Smocks

PURCHASE ON LINE

Shopping Cart!

 

 

VIEW THIS SITE IN

Spanish

 

0
[Back] Home / ESD Monitors / ESD Monitors ST 020

ESD Monitors ST 020 Installation & Specifications

Note A calibration / test unit is available for the ST-020. Simply plug the ground cable into the common point ground and the operator cable into the operator input. The LED should be red. It should be Green when you press the "test" button.

Specifications

Size (h.w.d): 1"x 2.4" x 2.3"
Mounting Velcro (supplied)/optional bracket
Operator Fault Condition = Greater than 10 Meg Ohm
Bench mat Fault Condition = Greater than 10 Meg Ohm
Power 115 VAC, 60 Hz Power Pack
Visual Alarm Dual Color LED Indicators: Green = Safe, Red = Fault
Audio Alarm Piezo Buzzer
Operation Automatic, Unit is activated when operator plugs wrist strap connector into jack

Installation

ESD_Mo13
  • Mount the AEI-ST020 in a convenient place on the workbench using the velcro supplied with the unit or the optional mounting bracket. The units are frequently mounted on the underside of the workbench to keep them out of the way.
  • Plug the power adaptor into the ST-020 and into a grounded outlet. Both LEDs should turn red and the buzzer should sound. The ground in the outlet is an important part of the system and should also be connected to the ESD common point ground. The outlet and the common point ground can be located at any convenient place on the workbench
  • Plug the bench cable into the back of the unit and connect it to the bench mat. It should be connected to the opposite side of the mat from the mat ground connection. The bench LED should turn green
  • Note The 020 and 030 series monitors are designed to work in the static conductive range of matting but work well with static dissipative tri layer matting (like our and UltraComfort or UltraTough) or dual layer matting with a conductive bottom layer and static dissipative top layer (like our ElectraTherm ESD rubber matting). If using tri layer static dissipative matting the unit (and ground connection from the matting) must make contact with the conductive inner layer of the esd mat. To insure this contact use either our push and cinch or mat snap kit. Many customers hardwire the bench cable to the fastener (the unit is supplied standard with an alligator attachment) or use the optional snap attachment
  • Plug a wrist strap into the front of the unit and put it on. The operator LED should turn green. If it doesn't, touch the wrist strap to the common point ground. If the operator LED turns green then the wrist strap was not making good contact with the operators wrist
  • 4
  • If incorporating with the network monitoring system: plug the grey flat cable into the back of the ST-020 and into the AEI NMH. Verify that the NMH status is the same as the LED on the front of the ST020

We manufacture custom cut table top mats that work great with these monitors. If you're manufacturing your own, our UltraComfort, UltraTough and UltraStrong are prefect choices!

  • ESD Flooring
  • |
  • Mats
  • |
  • ESD Floor Care Products
  • |
  • ESD Ionizers
  • |
  • Ultrastat2000.com

new esd flooring products for 04/05/10

TERMS CONDITIONS AND YOUR PRIVACY 
This site is protected by copyright and trademark laws under US and International law.

United Static Control Products Inc
 

4878 Lake View Circle

Colorado City, CO 81019

United States of America