Specifications:ESD sheet flooring, eSd floor tile

	*Tame the Static Beast!*
ESD FLOORING OPTIONS		HOME
ESD EPOXY		ESD WAX
ESD VINYL ROLL GOODS		ESD CARPETING
MORE ESD VINYL TILES		E MAIL UNITED

ElectraFloor Static Control flooring Main Page

ElectraFloor
Specifications: ESD sheet flooring, eSd floor tile

Popular Designer Colors
Options in Conductivity
Roll goods or Tiles
Outstanding longevity
Low (to no) maintenance
High shine or low glare finish

Physical Specifications:

Gauge: 2.0 mm
Sheet Width: 2m
Sheet Length: 20m
Roll Size: 40 m²
Weight: 3.50 kg/m²
Tile Size: 608 mm x 608 mm

Flame Spread and Smoke Emissions:

BS; 476 Part 7, 1987: Class 2
Din 4102: B1
ASTM E648: Class 1
AS 1530.3: Flame Spread 0

Light Fastness: >7

In Use Area Classification per EN 685: 34/43

Electrical Resistance: ElectraFloor Static Conductive

PTP: 5.1 x 10 ⁴to 2.5 x 10 ⁶ @ 10 Volts
RTG: 5.1 x 10 ⁴to 2.5 x 10 ⁶ @ 10 Volts

Electrical Resistance: ElectraFloor Static Dissipative:

PTP: 1.1 x 10 ⁷to 5.5 x 10 ⁹ @ 100 Volts*
RTG: 1.1 x 10 ⁶ to 8.5 x 10 ⁸ @ 100 Volts*

Abrasion Resistance: EN 649: 1996, Group P

Chemical Resistance: ElectraFloor has good resistance to dilute acids and alkalis. Chemical resistance charts by shade are available on request

Static load limit: Per ASTM F-970

Extended Electrical Testing by United ESD

Below: our test results after installation at two Facilities (both approximately 70,000 sq/ft each, one in Mexico, one in California). Testing was performed in accordance with industry accepted standards of EOS ESD 7.1. These floors were installed "on grade" and on cement. Further, the floors were grounded utilizing the advanced parameters shown in How to Ground your new ESD Floor. Your results may vary due to substrate, substrate conditions and environmental conditions prevalent in your location.

*Tested at a relative humidity > 45%.

As is the case with many of the modern ESD Vinyl's, ElectraFloor is designed to work as a system in conjunction with our conductive adhesives. When testing uninstalled, this static dissipative material (without the adhesive) ElectraFloor SD will show a slightly higher resistance value than those posted in our electrical specifications (prevalent only with the static dissipative materials). ElectraFloor static dissipative is designed with a built in resistance value that provides added safety to employees that may come into contact with higher voltage / amperage power sources. This added resistance has shown minimal effect in it's ability to drain ESD potential (static decay potential).

wpeA.jpg (15654 bytes)

wpeC.jpg (18290 bytes)

Maintenance:

Maintenance is dependant on the nature and intensity of traffic and the specific requirements of the end user. To keep cost low, without compromising standards of hygiene and cleanliness, United ESD recommends that a maintenance regime be specifically tailored to your needs. Polishes or floor finishes that inhibit the floors electrical performance must not be used. Remove abrasives by sweeping on a regular basis. Damp mop with warm water and approved UltraStat 2000 ESD Cleaning solution as needed. A clean floor insures consistent electrical performance. ElectraFloor ESD Vinyl is initially supplied with a non-glare finish. If your needs require a high shine, simply burnish the material with a high speed floor buffing machine. Contact United ESD for further recommendations.

Installation Overview

ElectraFloor flooring Main Page

More ESD flooring

United ESD Incorporated

POB 19252, 4878 Lake View Circle

Colorado City, CO 81019

United States of America

Direct: 719.676.3928