Pale Gray, PN: Ti481	Dark Gray, PN: Ti482	Electronic Blue, PN: Ti483	Clean White, PN: Ti480

Type	Availability	Weight
Rolls	4'6" x 66' x .080" gauge (297 SF per roll)(1.4m x 20m x 2.0mm gauge)	297 sft./roll = 185 lbs./roll (84 Kg/box)
Tiles	24" x 24" x .080" gauge (608 x 608mm x 2.0 mm gauge)	15 tiles/box (60 sft.) Weight/box 38 lbs. (18 Kg/box)
ESD Welding Rod	-	330 Linear feet per spool

ElectraFloor Titanium Series semi gloss permanently esd conductive solid vinyl industrial flooring product. Roll goods may be used as mats or flooring. Titanium Series ESD Flooring is manufactured in the European Union for United Static Control Products Incorporated, PO Box 19252, Colorado City CO 81019. The material shall be manufactured as a co-extruded 4' 6" x 66' x .080 gauge sheet or 24" x 24" x .080 gauge tile with a hard wear resistant esd conductive top layer and a flexible full surface esd conductive supporting layer in a semi gloss finish.

Surface Resistivity Point to Point (PTP per EOS ESD S 7.1)	>1.0E04 <1.0E06 (esd conductive)
Electrical Resistance to Ground (RTG per EOS ESD S 7.1)	>1.0E04 <1.0E06 (esd conductive)
Flooring Radiant Panel: NFPA 253: Critical Radiant Flux	0.73 W/cm2, Class 1
Flooring Radiant Panel: NBSIR 75-950: Critical Radiant Flux	Pass, Class 1
Flooring Radiant Panel: ASTM-648: Critical Radiant Flux	0.73 W/cm2, Class 1
Smoke Density, ASTM E-662; NFPA 258; Average optical density in burning / smoldering mode	<450
Residual Indentation LF-475A	0.002 average
Abrasive Wear, Taber H-18 wheel, 5,000 cycles, 1,000 gm weight	1.1% loss of weight
Abrasive Wear, Taber H-18 wheel, 1,000 gm weight to wear layer penetration (end point)	>20,000 cycles, (2.0% loss of weight)
Static coefficient of friction, ASTM D-2047-03, James Test average wet, dry leather	.60 approx.
Static load limit DIN 16961.2	>1,000 P.S.I.
Charge decay time per FTMS 4046-101c	<.17 seconds

Titanium: The powerful new element in ESD floors for static control

Utilizing our approved specialty conductive adhesives allows installation simply unheard in the past. When used in conjunction with our unique no residue VOC free textile reinforced double sided adhesive, or our new United 2450 liquid conductive adhesive (voc free and CA proposition 65 compliant) Titanium can be installed over existing epoxy, VCT, non porous hard troweled concrete, painted surfaces, concrete and more. Your needs dictate: permanently bonded or installed in a mode that allows removal and redeployment of the material in a different area! Titanium, the ultimate choice for clean rooms, electronic and sophisticated product development, manufacturing, command centers and more. With specifications that meet or exceed the latest most stringent standards including the new ANSI EOS ESD S 2020 2007.

Why Sheet goods?

Titanium Series esd flooring is available in sheet goods (or optional tiles) for a very good reason. Let's look at a 150' x 60' area. A typical 1' x 1' ESD tile will have over 18,000 linear feet (nearly 4 miles of seams)! Take a look at this 3M esd tile floor. Bad tiles? Poor install? Not at all. Unfortunately tiles don't always fit perfectly and the installer must adjust (leave small spaces between the tiles) as the installation progresses (some tiles even shrink over a period of time).

And/or the substrate isn't flat leaving an uneven profile (slight highs and lows) to the finished install. Minute spaces between the tiles and/or deviations in the flatness, a perfect environment for contaminant and dirt entrapment. On a standard tile floor these deviations typically present little problem, they are often filled in with floor wax. Esd floor finish shouldn't be a necessity for a quality esd floor. It raises the insulative properties, can wreak havoc in a clean room (from powdering), is expensive and can be a maintenance application nightmare!

Titanium sheet goods, same area? less than 2,000 linear feet of seams and these seams are heat welded for the ultimate in cleanliness and ease of maintenance.