Colorado	Connecticut	Texas
Massachusetts	Washington	California

Click to expand. Tribocharge Testing per 97.2 Concrete Substrate Perfect for Class 0 ESD Control Areas	Click to expand. Resistance to ground via S7.1 Comparison of EG to ESD Tile Concrete substrate	Click to expand. Electrical Resistance flooring, technician and heel grounders per ESD 97.1, concrete substrate

New concrete substrates should be allowed to cure for at least sixty days prior to application of this product. Applications to floors colder than 60 ⁰ F is not recommended. Sweep and vacuum flooring substrate. If contaminated mop with, a neutral degreaser to remove oil, grease and soil. For exceedingly smooth troweled concrete, concrete that does not readily absorb water, sealed concrete or concrete coated with parting compounds the concrete may be etched with standard concrete etching solutions diluted per manufacturers recommendations, thoroughly rinse with water and allow to dry overnight. Etching may generally be replaced by screen disking or sanding (80 grit pads or rougher) If substrate has been previously coated, a small area should be cleaned and roughed up by a screen disking with a 80 grit screen. Test ElectraGuard for adhesion, lifting etc. Any areas of the existing coating which display poor adhesion should be stripped. Wash the stripped areas, acid rinse, thoroughly rinse with water and allow to fully dry prior to application of ElectraGuard. Catalyzed ElectraGuard should be used within six hours of mixing, therefore prepare only the quantity necessary for immediate use. Add the pre-measured catalyst to epoxy base. Stir gently until the catalyst has been thoroughly mixed in. Allow catalyzed mixture to stand 5 minutes. Apply catalyzed material with a short nap roller in thin uniform coats. The initial coat will cover approximately 250 to 500 ft 2 per gallon. Second coat coverage is approximately 400 to 600 ft 2 per gallon. A third coat provides optimum esthetics and is highly recommended. Due to it's reduced solids count and thin set benefits ElectraGuard may exhibit slight variances in texture and color depending on the substrate of application. These variances do not affect the excellent electrical performance or wear characteristics.  This product is available in gray, light gray, beige and green and as applied features a non glare matt finish. Should high shine be desired consider sealing the ElectraGuard with ElectraThane and ElectraGlaze (see application instructions for details) Application Instructions

• Dust Mop Daily
• Damp mop weekly using a diluted solution of ElectraClean and water.
  Note: Never use plain water or other floor cleaning chemicals as this may leave an insulative residue.
• Auto Scrub every two months or as needed to remove ground in dirt and contaminants, start with lightest pad possible.
• As needed, high speed polish using a white or champagne colored pad and ElectraShine polishing spray.
• As needed (about every year or two). Follow the ESD floor care procedure as listed at How to maintain an esd floor.

Standard Colors	Medium Gray, Light Gray, Emerald Green and Beige Medium Gray, Pantone 430. Light Gray, Pantone 538. Beige, Pantone 401 New: ROHS GREEN.
Solids	39% +/- 1%
Static Charge Decay	<0.1 sec. per FTMS 101B, Method 4046
Charge Generation	ESD STM 97.2 <25 V (on standard concrete substrate)
pH	6.0 - 7.0
Weight per Gallon	9.5 - 9.6 pounds
Hardness	30 (Sward)
Viscosity	H - J (Gardner)
Solvents	Water - Glycol
Flash Point	160o
Dry Time	Touch; 7 hours
Moderate traffic	12hours, Full cure 7 days
Coverage	250 - 600 ft 2 per gallon
Resistivity per ANSI ESD S20.20-2007, 97.1	Meets ESD S 20.20-2007, 97.1 @ <3.5E07. *Properly agitated and grounded ElectraGuard applied to bare unsealed concrete

Part Number: EG1X4 Availability: 4 ea 1  gallon containers (1 case) Pricing: $478.07	Part Number: EG1X5 Availability: 1 ea 5 Gallon Container Pricing: $560.47
Coverage 1st coat: 250 to 500 SF per gallon ($0.49 - 0.24)*	Coverage 1st coat: 250 to 500 SF per gallon ($0.48 - 0.24)*
Coverage 2nd coat: 400 to 600 SF per gallon ($0.31 - 0.20)	Coverage 2nd coat: 400 to 600 SF per gallon ($0.30 - 0.20)
Coverage 3rd coat: 500 to 600 SF per gallon ($0.24 - 0.20)	Coverage 3rd coat: 500 to 600 SF per gallon ($0.24 - 0.20)
Average cost per SF (3 coats) $0.64 to $1.04 per S.F.	Average cost per SF (3 coats) $0.63 to $1.03 per S.F.

Today's reality dictates an increasingly daunting task. Electrostatic thresholds are dropping significantly requiring an unprecedented higher level of static control flooring performance at a time when funding has become more of an issue. Now (more than ever) ESD flooring must be selected by proven long term performance, electrical reliability and installed cost. In addition, esd flooring must meet the newest standards of ANSI/ESD S20.20-2007 and be positioned to meet standards yet to be written. It must be easy to maintain, capable of handling a multitude of traffic, be aesthetically pleasing and never NEVER stop working. At United we provide the most extensive selection of static control flooring in the industry. It's up to our clients and the industries they represent to select the most popular. ElectraGuard Elite; Our most popular esd floor covering for numerous reasons. Long and Short - You can pay more but you'll never find a better hard surface esd floor for the money!